Overview

The MCUXpresso SDK provides a peripheral driver for the System Mode Controller (SMC) module of MCUXpresso SDK devices. The SMC module sequences the system in and out of all low-power stop and run modes.

API functions are provided to configure the system for working in a dedicated power mode. For different power modes, SMC_SetPowerModexxx() function accepts different parameters. System power mode state transitions are not available between power modes. For details about available transitions, see the power mode transitions section in the SoC reference manual.

Typical use case

Enter wait or stop modes

SMC driver provides APIs to set MCU to different wait modes and stop modes. Pre and post functions are used for setting the modes. The pre functions and post functions are used as follows.

Disable/enable the interrupt through PRIMASK. This is an example use case. The application sets the wakeup interrupt and calls SMC function SMC_SetPowerModeStop to set the MCU to STOP mode, but the wakeup interrupt happens so quickly that the ISR completes before the function SMC_SetPowerModeStop. As a result, the MCU enters the STOP mode and never is woken up by the interrupt. In this use case, the application first disables the interrupt through PRIMASK, sets the wakeup interrupt, and enters the STOP mode. After wakeup, enable the interrupt through PRIMASK. The MCU can still be woken up by disabling the interrupt through PRIMASK. The pre and post functions handle the PRIMASK.
Disable/enable the flash speculation. When entering stop modes, the flash speculation might be interrupted. As a result, pre functions disable the flash speculation and post functions enable it.

SMC_PreEnterStopModes();
/* Enable the wakeup interrupt here. */
SMC_SetPowerModeStop(SMC, kSMC_PartialStop);
SMC_PostExitStopModes();

Data Structures
struct	smc_power_mode_lls_config_t
	SMC Low-Leakage Stop power mode configuration. More...

struct	smc_power_mode_vlls_config_t
	SMC Very Low-Leakage Stop power mode configuration. More...

Enumerations
enum	smc_power_mode_protection_t { kSMC_AllowPowerModeVlls = SMC_PMPROT_AVLLS_MASK, kSMC_AllowPowerModeVlp = SMC_PMPROT_AVLP_MASK, kSMC_AllowPowerModeAll }
	Power Modes Protection. More...

enum	smc_power_state_t { kSMC_PowerStateRun = 0x01U << 0U, kSMC_PowerStateStop = 0x01U << 1U, kSMC_PowerStateVlpr = 0x01U << 2U, kSMC_PowerStateVlpw = 0x01U << 3U, kSMC_PowerStateVlps = 0x01U << 4U, kSMC_PowerStateVlls = 0x01U << 6U }
	Power Modes in PMSTAT. More...

enum	smc_run_mode_t { kSMC_RunNormal = 0U, kSMC_RunVlpr = 2U }
	Run mode definition. More...

enum	smc_stop_mode_t { kSMC_StopNormal = 0U, kSMC_StopVlps = 2U, kSMC_StopVlls = 4U }
	Stop mode definition. More...

enum	smc_stop_submode_t { kSMC_StopSub0 = 0U, kSMC_StopSub1 = 1U, kSMC_StopSub2 = 2U, kSMC_StopSub3 = 3U }
	VLLS/LLS stop sub mode definition. More...

enum	smc_partial_stop_option_t { kSMC_PartialStop = 0U, kSMC_PartialStop1 = 1U, kSMC_PartialStop2 = 2U }
	Partial STOP option. More...

enum	_smc_status { kStatus_SMC_StopAbort = MAKE_STATUS(kStatusGroup_POWER, 0) }
	SMC configuration status. More...

Driver version
#define	FSL_SMC_DRIVER_VERSION (MAKE_VERSION(2, 0, 3))
	SMC driver version 2.0.3. More...

System mode controller APIs
static void	SMC_SetPowerModeProtection (SMC_Type *base, uint8_t allowedModes)
	Configures all power mode protection settings. More...

static smc_power_state_t	SMC_GetPowerModeState (SMC_Type *base)
	Gets the current power mode status. More...

void	SMC_PreEnterStopModes (void)
	Prepares to enter stop modes. More...

void	SMC_PostExitStopModes (void)
	Recovers after wake up from stop modes. More...

static void	SMC_PreEnterWaitModes (void)
	Prepares to enter wait modes. More...

static void	SMC_PostExitWaitModes (void)
	Recovers after wake up from stop modes. More...

status_t	SMC_SetPowerModeRun (SMC_Type *base)
	Configures the system to RUN power mode. More...

status_t	SMC_SetPowerModeWait (SMC_Type *base)
	Configures the system to WAIT power mode. More...

status_t	SMC_SetPowerModeStop (SMC_Type *base, smc_partial_stop_option_t option)
	Configures the system to Stop power mode. More...

status_t	SMC_SetPowerModeVlpr (SMC_Type *base)
	Configures the system to VLPR power mode. More...

status_t	SMC_SetPowerModeVlpw (SMC_Type *base)
	Configures the system to VLPW power mode. More...

status_t	SMC_SetPowerModeVlps (SMC_Type *base)
	Configures the system to VLPS power mode. More...

status_t	SMC_SetPowerModeVlls (SMC_Type base, const smc_power_mode_vlls_config_t config)
	Configures the system to VLLS power mode. More...

Data Structure Documentation

struct smc_power_mode_lls_config_t

Data Fields
bool	enableLpoClock
	Enable LPO clock in LLS mode.

struct smc_power_mode_vlls_config_t

Data Fields
smc_stop_submode_t	subMode
	Very Low-leakage Stop sub-mode.

bool	enablePorDetectInVlls0
	Enable Power on reset detect in VLLS mode.

bool	enableLpoClock
	Enable LPO clock in VLLS mode.

Macro Definition Documentation

#define FSL_SMC_DRIVER_VERSION (MAKE_VERSION(2, 0, 3))

Enumeration Type Documentation

enum smc_power_mode_protection_t

Enumerator
kSMC_AllowPowerModeVlls	Allow Very-low-leakage Stop Mode.
kSMC_AllowPowerModeVlp	Allow Very-Low-power Mode.
kSMC_AllowPowerModeAll	Allow all power mode.

enum smc_power_state_t

Enumerator
kSMC_PowerStateRun	0000_0001 - Current power mode is RUN
kSMC_PowerStateStop	0000_0010 - Current power mode is STOP
kSMC_PowerStateVlpr	0000_0100 - Current power mode is VLPR
kSMC_PowerStateVlpw	0000_1000 - Current power mode is VLPW
kSMC_PowerStateVlps	0001_0000 - Current power mode is VLPS
kSMC_PowerStateVlls	0100_0000 - Current power mode is VLLS

enum smc_run_mode_t

Enumerator
kSMC_RunNormal	Normal RUN mode.
kSMC_RunVlpr	Very-low-power RUN mode.

enum smc_stop_mode_t

Enumerator
kSMC_StopNormal	Normal STOP mode.
kSMC_StopVlps	Very-low-power STOP mode.
kSMC_StopVlls	Very-low-leakage Stop mode.

enum smc_stop_submode_t

Enumerator
kSMC_StopSub0	Stop submode 0, for VLLS0/LLS0.
kSMC_StopSub1	Stop submode 1, for VLLS1/LLS1.
kSMC_StopSub2	Stop submode 2, for VLLS2/LLS2.
kSMC_StopSub3	Stop submode 3, for VLLS3/LLS3.

enum smc_partial_stop_option_t

Enumerator
kSMC_PartialStop	STOP - Normal Stop mode.
kSMC_PartialStop1	Partial Stop with both system and bus clocks disabled.
kSMC_PartialStop2	Partial Stop with system clock disabled and bus clock enabled.

enum _smc_status

Enumerator
kStatus_SMC_StopAbort	Entering Stop mode is abort.

Function Documentation

static void SMC_SetPowerModeProtection	(	SMC_Type *	base,
		uint8_t	allowedModes
	)

inlinestatic

This function configures the power mode protection settings for supported power modes in the specified chip family. The available power modes are defined in the smc_power_mode_protection_t. This should be done at an early system level initialization stage. See the reference manual for details. This register can only write once after the power reset.

The allowed modes are passed as bit map. For example, to allow LLS and VLLS, use SMC_SetPowerModeProtection(kSMC_AllowPowerModeVlls | kSMC_AllowPowerModeVlps). To allow all modes, use SMC_SetPowerModeProtection(kSMC_AllowPowerModeAll).

Parameters

base	SMC peripheral base address.
allowedModes	Bitmap of the allowed power modes.

static smc_power_state_t SMC_GetPowerModeState ( SMC_Type * base )

inlinestatic

This function returns the current power mode status. After the application switches the power mode, it should always check the status to check whether it runs into the specified mode or not. The application should check this mode before switching to a different mode. The system requires that only certain modes can switch to other specific modes. See the reference manual for details and the smc_power_state_t for information about the power status.

Parameters

base	SMC peripheral base address.

Returns: Current power mode status.

void SMC_PreEnterStopModes ( void )

This function should be called before entering STOP/VLPS/LLS/VLLS modes.

void SMC_PostExitStopModes ( void )

This function should be called after wake up from STOP/VLPS/LLS/VLLS modes. It is used with SMC_PreEnterStopModes.

static void SMC_PreEnterWaitModes ( void )

inlinestatic

This function should be called before entering WAIT/VLPW modes.

static void SMC_PostExitWaitModes ( void )

inlinestatic

This function should be called after wake up from WAIT/VLPW modes. It is used with SMC_PreEnterWaitModes.

status_t SMC_SetPowerModeRun ( SMC_Type * base )

Parameters

base	SMC peripheral base address.

Returns: SMC configuration error code.

status_t SMC_SetPowerModeWait ( SMC_Type * base )

Parameters

base	SMC peripheral base address.

Returns: SMC configuration error code.

status_t SMC_SetPowerModeStop	(	SMC_Type *	base,
		smc_partial_stop_option_t	option
	)

Parameters

base	SMC peripheral base address.
option	Partial Stop mode option.

Returns: SMC configuration error code.

status_t SMC_SetPowerModeVlpr ( SMC_Type * base )

Parameters

base	SMC peripheral base address.

Returns: SMC configuration error code.

status_t SMC_SetPowerModeVlpw ( SMC_Type * base )

Parameters

base	SMC peripheral base address.

Returns: SMC configuration error code.

status_t SMC_SetPowerModeVlps ( SMC_Type * base )

Parameters

base	SMC peripheral base address.

Returns: SMC configuration error code.

status_t SMC_SetPowerModeVlls	(	SMC_Type *	base,
		const smc_power_mode_vlls_config_t *	config
	)

Parameters

base	SMC peripheral base address.
config	The VLLS power mode configuration structure.

Returns: SMC configuration error code.

Overview

Typical use case

Enter wait or stop modes

Data Structures

Enumerations

Driver version

System mode controller APIs

Data Structure Documentation

Data Fields

Data Fields

Macro Definition Documentation

Enumeration Type Documentation

Function Documentation